In this post, I want to share a successful experience from a customer. He updated his Opel/Vauxhall CD30/CD30 MP3 to CDC40 with the Tech 2 Scanner which bought from obd2tool. The following is his guide and help Opel owners to have advanced Audio display.
Tools you will need:
GM Tech2 Diagnostic Tool Opel 32MB card or OP-COM CAN OBD diagnostic interface
Blaupunkt car CDC40
How to:
Turn on the dashboard
Connect Car Diagnostic Tool Tech2 scanner to Opel/ Vauxhall OBD port by using the OBD2 cable
Turn ignition ON
Disable below anti-theft protection modules with Tech2 scanner by following steps
EHU -> Code Index -> 001_02
Enable the anti-theft protection:
GID / CID
UHP
EHU
Turn off the dash and disconnect Tech2 scanner
Remove the CD30 / CD30 mp3 using the appropriate accessories. You will need to disconnect the antenna wire and the connector big loosening the locking device that engages in the lower part of the connector
Replace the original antenna with the appropriate terminal for receiving digital signals:
Unscrew the existing antenna
Disconnect the sky (just ask for details)
Unscrew the nut holding the antenna base
To avoid replacing the entire cable I... More
by obd2tools on 2019-05-28 11:03:00
[Done] 2014 Audi A3 MQB odometer correction via OBD with OBDSTAR X300 DP PLUS. This post comes with the step by step procedure.
2014 Audi A3 with MQB.
Current value: 48728KM on the dashboard.
Plug OBDSTAR key master DP Plus to the OBD port of Audi A3, boot the machine, tap ” Immobilizer”, then “Audi”, newest “Audi V31.74”.
Initializing…
Initializing diagnostic data…
Authorizing…
Tap “A3”.
Tap ” MQB 2014.06 -”
Read the message “Only MQB dashboard of Continental and VDO supported”.
Switch ignition on.
Mileage adjustment.
Confirm the current mileage is 48728KM.
Input 50000.
Communicating…
Logging in system…
Data backup…
Adjust Success…
Have 50000KM on the dashboard.
Done.
Don’t you think it is so easy to adjust mileage for 2014 Audi A3 with OBDSTAR DP Plus.
FYI, OBDSTAR DP Plus (in orange color) = OBDSTAR Key master DP (in green color)
by obd2tools on 2019-05-19 01:20:45
KTAG V7.020 sw 2.25 is verified working great, it has an improved onscreen message management, it can read the gearbox sensor on Magneti Marelli 8GMK ECUs. The following paragraphs will offer Ktag 2.25 download free link on mega, carlist, installation and feedback.
Ktag 2.25 free download on mega
https://mega.nz/#!REpxwY5D!8FIo0maWqHbmEvHnTskmDVb68YLcZQQyoda5NHrapms
Works on XP, WIN7 (Try on WIN8 WIN10 at your own lucky)
Works on almost all Kess master
***But SE135 has a different driver, so their installation method is a little different.
Ktag 2.25 car list:
https://share.weiyun.com/57X8G6n Password: 46ip19
1.How to update Ksuite 2.25 from 2.23 and read/write ECU data (SE135)?
Steps on how to update Ksuite 2.25 from 2.23:
Open “Ksuite_ 223_V2” to setup the wizard according to the prompt.
Get message “Connection not established”.
Right click on “Ksuite” on the desktop, choose “Properties”, select all files and delete them.
Open the folder “Ksuite 2.25”, copy all files except “Help”, paste them to Kusite 2.23 folder to replace the same files.
Copy the “Help” folder from ” Kusite 2.23″ to ” Kusite 2.25″
Plug KTM100 FW V7.020... More
by obd2tools on 2019-05-10 10:59:01